Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
IGO-s conversion
#11
These two places claim they have it:

http://www.healthcabin.net/ud-youde-igol-rda-atomizer-p/8897.html

http://www.thebestshop.eu/shop/rebuildable-atomizers/242-igo-l-rebuildable-atomizer.html

There are also on DXGate, but min 10 pieces per order:

http://www.dhgate.com/wholesale/search.do?act=search&sus=&searchkey=IGO-L
[Image: UbOpoPW.gif]
[-] The following 2 users Like MacVap's post:
  • cheekiecharlie, keepitgoin
Reply
#12
thats a great deal at the best shop , only 99p each ,im just about to buy 3 then £4 postage is reasonable too
vaping is a passion not just a hobby




[Image: tumblr_n5adqxP4Vu1qm8o2po3_r1_250.gif]
Reply
#13
It's Euros Charlie!! Even cheaper!! I ordered 1 to Mod, and some to practise on!

(11-07-2016, 02:44 PM)MacVap Wrote: These two places claim they have it:

http://www.healthcabin.net/ud-youde-igol-rda-atomizer-p/8897.html

http://www.thebestshop.eu/shop/rebuildable-atomizers/242-igo-l-rebuildable-atomizer.html

There are also on DXGate, but min 10 pieces per order:

http://www.dhgate.com/wholesale/search.do?act=search&sus=&searchkey=IGO-L

Thank you, thats my Vape Budget gone 'til 2017 then!!
Reply
#14
yes, 6.97 euros including delivery ,been looking for a few more, for their price they are hard to beat ,they give a great vape
vaping is a passion not just a hobby




[Image: tumblr_n5adqxP4Vu1qm8o2po3_r1_250.gif]
Reply
#15
They're pretty quick at the best shop, ordered a pair of igo-l's yesterday and they've been dispatched today. How easy is it to remove the centre pin et al? I tried a conversion of a clone derringer, but screwed up putting the pin back in and nobbled the 510.
Reply
#16
simple mate,if you have an atty vice or just a normal vice, open the jaws so the 510 sits in the gap and the atty body sitting on top of the jaws, then just gently tap the pin down through the 510 from the top, its just held in by the insulator,

then its just a matter of cutting a slit in the insulator , 1-2mm is enough ,make sure the slit lines up with the edge of the screw at the bottom , (if its a flat pin ,you will need to dremmel a small slit in it) then the juice has a free path to get into the atty

it may sound daunting ,but is really easy and takes minutes to do , next one i do ,i will take step by step pics and post it up
vaping is a passion not just a hobby




[Image: tumblr_n5adqxP4Vu1qm8o2po3_r1_250.gif]
[-] The following 4 users Like cheekiecharlie's post:
  • Berk, keepitgoin, vern, wobbly
Reply
#17
Cheers.
Reply
#18

"...it may sound daunting ,but is really easy and takes minutes to do , next one i do ,i will take step by step pics and post it up
"
That would be brilliant Charlie, if you're up for it!!!
Always easier for me if I can see how it's done, as well as read the steps.
Would it be worthwhile creating a Thread where Members can show Modding tips for Atties and Devices?

I'm thinking (dreaming) of building a Sqounker, Dual Series 18650, and have been looking at Modmaker UK for bit's + Chips.
I need to get my head round Variable Voltage and how it will affect my Vaping style first!
I use Mechs occasionally, but mostly Regulated Devices, with YiHi chips. I just got my first DNA, a Squonking DNA 40 Big Grin
My Vaping style isn't much above 20w at most, on Regulated Mods, so I look for long run time from my devices and reliability.
This Vaping lark has rekindled a long held desire to build Electronic Circuitry and it's an opportunity to learn I think I need as I get older.
I'll be getting a Shed next Blush
Reply
#19
yes, i think it would be a good idea for a thread ,building a mod is relatively easy too, i started with the little 14500 kits from rob at stealth , then started buying bits here and there, modmaker has loads now,i only ever build mechs, parallel and series, some with mosfet some without, building a squonker is at the top of my list, but deciding what to do is my first hurdle
vaping is a passion not just a hobby




[Image: tumblr_n5adqxP4Vu1qm8o2po3_r1_250.gif]
Reply
#20
My two arrived this morning, threw a quick build in to one to try it out.

[Image: UiUe4At.jpg?1]

I think this may be my first RDA that doesn't have post holes, so that was a new challenge. 27g kanthal, 6 wraps, dead on 1ohm according to my IPV D2. EVL drip tip that looks like it was custom made for this dripper.
Interestingly it didn't register on my Smok ohm reader, so I don't hold out any hopes that it will fire on the dripbox, in fact I just tried on the dripbox and no joy.

It's rather good, although I might see about opening the air hole slightly in the future, I'm quite chuffed for less than £2.50 a piece (including postage).
Reply




Users browsing this thread: 1 Guest(s)